Emerson Rosemount 3812 Maintenance And Troubleshooting Manual Download Page 74

Page: 74 / 132

NOTICE

Feed-thru foam seals tear easily. Carefully pull the transducer cables through the
seal to prevent ripping the feed-thru cable seal.

27. Reattach the Base Enclosure to the upper split shroud and the meter body with the

three shoulder washers, flat washers, split lock washers and hex head bolts. Tighten
the bolts with a 7/16 inch (11 mm) socket driver.

Figure 3-38: Base Enclosure assembly

A. 7/8 hex head bolts (3)

B. Split lock washers (3)

C. Flat washers (3)

D. Nylon shoulder washers (3)

E. O-ring

F. Base enclosure

28. Apply Loctite

nickel anti-seize or equivalent to the three hex head bolts to prevent

loosening due to vibration during operation.

29. Place the Acquisition Module into the Base Enclosure, align the thee holes of the

Acquisition Module with the three holes in the base enclosure and secure with the
three split lock washers and flat head screws (see

Figure 3-39

). Position the cables

Meter maintenance

Maintenance and Troubleshooting Manual

April 2022

00809-0100-3812

Emerson.com/Rosemount

Summary of Contents for Rosemount 3812





































































































































Search results

Summary of Contents for Rosemount 3812

Reviews:

Related manuals for Rosemount 3812

Brands by name

Popular brands

Emerson Rosemount 3812, Maintenance And Troubleshooting Manual

Search results

Summary of Contents for Rosemount 3812

Reviews:

Related manuals for Rosemount 3812

Brands by name

Popular brands