Emerson Rosemount 2240S Reference Manual Download

Page: 90 / 194

Reference Manual

00809-0100-2240, Rev DA

Configuration/Operation

October 2017

Configuration/Operation

5.11.3

Application example

This example shows a Rosemount 2240S Multi-Input Temperature Transmitter configured for receiving
level measurement data from a level device such as the Rosemount 5900S Radar Level Gauge.

Figure 5-15. Function block configuration of a Rosemount 2240S using DeltaV

™

Control Studio

Note that XD_SCALE units must be the same in the AI block and the AO block.

CAS_IN=Remote set point value from another function block
OUT=Block output and status.

Summary of Contents for Rosemount 2240S



































































































































































































Search results

Summary of Contents for Rosemount 2240S

Reviews:

Related manuals for Rosemount 2240S

Brands by name

Popular brands

Emerson Rosemount 2240S, Reference Manual

Search results

Summary of Contents for Rosemount 2240S

Reviews:

Related manuals for Rosemount 2240S

Brands by name

Popular brands