manualshive.com logo in svg

Emerson Rosemount 2240S, Reference Manual, Page: 75 / 194

Share
Download
Emerson Rosemount 2240S Reference Manual Download Page 75

65

Reference Manual 

00809-0100-2240, Rev DA

Configuration/Operation

October 2017

Configuration/Operation

5.6

Configuration using TankMaster WinSetup

The TankMaster software package provides you with powerful and easy-to-use tools for installation and 
configuration of a Rosemount Tank Gauging system. See the 

Rosemount Tank Gauging System 

Configuration Manual

 for more information.

5.6.1

Advanced configuration

Average temperature calculation weight factor

You can specify a weight factor for each temperature element used in the tank average temperature 
calculation. This allows you to rate selected temperature elements with a larger impact on the average 
temperature calculation than the other elements. This is primarily used for LPG tanks.

Conversion methods

When using a resistance temperature element, the resistance values can be converted to temperature 
values by using:

a linearization table

a formula

an individual formula for each temperature element

For more information, see the 

Rosemount Tank Gauging System Configuration Manual

 for more 

information.

Summary of Contents for Rosemount 2240S



































































































































































































Reviews:

No comments