manualshive.com logo in svg

Emerson Rosemount 2240S, Reference Manual, Page: 13 / 194

Share
Download
Emerson Rosemount 2240S Reference Manual Download Page 13

3

Reference Manual 

00809-0100-2240, Rev DA

Introduction

October 2017

Introduction

1.3

Technical documentation

The Rosemount Tank Gauging System includes the following documentation:

Reference manuals

Rosemount Tank Gauging System Configuration Manual (00809-0300-5100)

Rosemount 2460 System Hub (00809-0100-2460)

Rosemount 2410 Tank Hub (00809-0100-2410)

Rosemount 5900S Radar Level Gauge (00809-0100-5900)

Rosemount 5900C Radar Level Gauge (00809-0100-5901)

Rosemount 2240S Multi-Input Temperature Transmitter (00809-0100-2240)

Rosemount 2230 Graphical Field Display (00809-0100-2230)

Rosemount 5300 Series Guided Wave Radar (00809-0100-4530)

Rosemount 5400 Series Radar Level Transmitter (00809-0100-4026)

Rosemount Tank Gauging Wireless System (00809-0100-5200) 

Rosemount TankMaster WinOpi (303028EN)

Product data sheets

Rosemount Tank Gauging System Data Sheet (00813-0100-5100)

Rosemount 2460 System Hub Product Data Sheet (00813-0100-2460)

Rosemount 2410 Product Data Sheet (00813-0100-2410)

Rosemount 5900S Product Data Sheet (00813-0100-5900)

Rosemount 5900C Product Data Sheet (00813-0100-5901)

Rosemount 2240S Product Data Sheet (00813-0100-2240)

Rosemount 2230 Product Data Sheet (00813-0100-2230)

Rosemount 5300 Product Data Sheet (00813-0100-4530)

Rosemount 5400 Product Data Sheet (00813-0100-4026)

Drawings

Table 1-1.  Installation drawings for the Rosemount 2240 Multi-Input Temperature Transmitter

Drawing

Issue

Title

D9240 041-912

2

Mechanical Installation Drawing

D9240 041-959

4

Electrical Installation Drawing 

D7000 001-798

2

System Installation Drawing Foundation fieldbus FISCO

D7000 001-811

1

System Installation Drawing Foundation fieldbus IS Entity

Summary of Contents for Rosemount 2240S



































































































































































































Reviews:

No comments