Emerson Rosemount 2240S Reference Manual Download Page 108

Page: 108 / 194

Reference Manual

00809-0100-2240, Rev DA

Configuration/Operation

October 2017

Configuration/Operation

4. See sections

“Water Level Sensor calibration” on page 53

and

“Water Level Sensor measuring range”

on page 55

for details on how to calibrate and configure the Water Level Sensor. These sections

describe the tank geometry and how to calculate the Level Offset (X) parameter.

OUNDATION

Fieldbus parameters:

TRANSDUCER BLOCK 1100>SB_STATUS
TRANSDUCER BLOCK 1100>WLS_CALIBRATION
TRANSDUCER BLOCK 1100>SB_UPPER_DEAD_ZONE
TRANSDUCER BLOCK 1100>SB_LOWER_DEAD_ZONE
TRANSDUCER BLOCK 1100>WATER_LEVEL

5. Click the

Finish

button to finish the WLS configuration and close the Sensor Setup window.

Summary of Contents for Rosemount 2240S



































































































































































































Search results

Summary of Contents for Rosemount 2240S

Reviews:

Emerson Rosemount 2240S, Reference Manual, Page: 108 / 194

Search results

Summary of Contents for Rosemount 2240S

Reviews: