Emerson Rosemount 2240S Reference Manual Download Page 176

Page: 176 / 194

166

OUNDATION

™

Fieldbus Block Information

OUNDATION

™

Fieldbus Block Information

October 2017

Reference Manual

00809-0100-2240, Rev DA

EU of PV_SCALE

The target block output value (set point).

SP_HI_LIM

EU of PV_SCALE

The highest set point value allowed.

SP_LO_LIM

EU of PV_SCALE

The lowest set point value allowed.

SP_RATE_DN

EU of PV_SCALE

per second

Ramp rate for downward set point changes. When the ramp rate is set

to zero, the set point is used immediately.

SP_RATE_UP

EU of PV_SCALE

per second

Ramp rate for upward set point changes. When the ramp rate is set to

zero, the set point is used immediately.

SP_WRK

EU of PV_SCALE

The working set point of the block. It is the result of set point

rate-of-change limiting. The value is converted to percent to obtain

the block’s OUT value.

Parameter

Units

Description

Summary of Contents for Rosemount 2240S



































































































































































































Search results

Summary of Contents for Rosemount 2240S

Reviews:

Emerson Rosemount 2240S, Reference Manual, Page: 176 / 194

Search results

Summary of Contents for Rosemount 2240S

Reviews: