Emerson Rosemount 2240S Reference Manual Download Page 194

Page: 194 / 194

Global Headquarters and Europe Regional Office
Tank Gauging

Emerson Automation Solutions

Box 150
(Visiting address: Layoutvägen 1)
SE-435 23 Mölnlycke

+46 31 337 00 00
+46 31 25 30 22
[email protected]

North America Regional Office
Tank Gauging

Emerson Automation Solutions

6005 Rogerdale Road
Mail Stop NC 136
Houston TX 77072
United States

+1 281 988 4000 or +1 800 722 2865
[email protected]

Latin America Regional Office

Emerson Automation Solutions

1300 Concord Terrace, Suite 400
Sunrise, FL 33323, USA

+1 954 846 5030
+1 954 846 5121
[email protected]

Asia Pacific Regional Office

Emerson Automation Solutions

1 Pandan Crescent
Singapore 128461

+65 6777 8211
+65 6777 0947
[email protected]

Middle East and Africa Regional Office

Emerson Automation Solutions

Emerson FZE P.O. Box 17033
Jebel Ali Free Zone - South 2
Dubai, United Arab Emirates

+971 4 8118100
+971 4 8865465
[email protected]

Linkedin.com/company/Emerson-Automation-Solutions

Twitter.com/Rosemount_News

Facebook.com/Rosemount

Youtube.com/user/RosemountMeasurement

Google.com/+RosemountMeasurement

Standard Terms and Conditions of Sale can be found on the

Terms and Conditions of

Sale page

The Emerson logo is a trademark and service mark of Emerson Electric Co.
Rosemount and Rosemount logotype are trademarks of Emerson.

HART is a registered trademark of the FieldComm Group.

All other marks are the property of their respective owners.
© 2017 Emerson. All rights reserved.

Reference Manual

00809-0100-2240, Rev DA

October 2017

Summary of Contents for Rosemount 2240S



































































































































































































Search results

Summary of Contents for Rosemount 2240S

Reviews:

Emerson Rosemount 2240S, Reference Manual, Page: 194 / 194

Search results

Summary of Contents for Rosemount 2240S

Reviews: