background image

29

Reference Manual 

00809-0100-2240, Rev DA

Rosemount

 2240S Installation

October 2017

Rosemount

 2240S Installation

4.2

Installation considerations

The information in this section covers installation considerations for the Rosemount 2240S Multi-input 
Temperature Transmitter in order to achieve a proper installation and optimum measurement 
performance. 

In order to reduce the required cabling, Rosemount Tank Gauging devices, including the Rosemount 
2240S, are designed for daisy-chain connection of the Tankbus and shield grounding to other field 
devices.

The Rosemount 2240S is designed for installation:

on top of the MST/WLS

remote on a pipe or wall

With remote mounting of the Rosemount 2240S, the nut and sleeve at the bottom of the 2240S can be 
replaced by a M32 cable gland, see 

“Components” on page 8

 and 

“Ordering information” on page 146

.

When the Rosemount 2240S transmitter is installed in a hazardous area, ensure that the installation 
requirements according to 

“Hazardous areas” on page 36

 are complied with.

Ensure that the recommended cable glands/conduits are used.

Ensure that the Tankbus is correctly terminated, se

“Termination” on page 37

.

Ensure that grounding is performed according to national and local electrical codes, see 

“Grounding” on 

page 34

.

Do not install the Rosemount 2240S in non-intended applications, for example environments where it 
may be exposed to extremely intense magnetic fields or extreme weather conditions.

Ensure that the Rosemount 2240S is installed such that it is not exposed to higher pressure and 
temperature than specified in 

Appendix A: Specifications and Reference Data

.

It is the responsibility of the user to ensure that the device meets the specific inside tank installation 
requirements such as:

chemical compatibility of wetted materials

design/operation pressure and temperature

Summary of Contents for Rosemount 2240S



































































































































































































Reviews: