manualshive.com logo in svg

Emerson Rosemount 2240S, Reference Manual, Page: 59 / 194

Share
Download
Emerson Rosemount 2240S Reference Manual Download Page 59

49

Reference Manual 

00809-0100-2240, Rev DA

Configuration/Operation

October 2017

Configuration/Operation

5.2.3

Configuration tools

Different tools are available for configuration of a Rosemount 2240S:

Rosemount TankMaster Winsetup

Field Communicator

AMS Device Manager for F

OUNDATION

™

 fieldbus systems

F

OUNDATION

 fieldbus hosts supporting DD4

TankMaster is an Emerson Automation Solutions/Rosemount Tank Gauging inventory management 
software package for installation and configuration of level gauging equipment. 

The WinSetup package provides you with powerful and easy-to-use tools for installation and 
configuration, see the 

Rosemount Tank Gauging System Configuration Manual

.

For DeltaV users, the DD can be found at www.easydeltav.com. For other hosts that use Device 
Descriptions (DD) and DD Methods for device configuration, the latest DD versions can be found on 
F

OUNDATION

’

S

 website at www.fieldbus.org. 

Summary of Contents for Rosemount 2240S



































































































































































































Reviews:

No comments