Emerson Rosemount 2240S Reference Manual Download Page 156

Page: 156 / 194

146

Specifications and Reference Data

October 2017

Reference Manual

00809-0100-2240, Rev DA

A.9 Ordering information

Table A-1. Rosemount 2240S Multi-input Temperature Transmitter ordering information

Model

Product Description

2240S

Multi-input Temperature Transmitter

Performance Class

Premium: ±0.05 °C (0.05 °F) instrument accuracy

Number of Temperature Sensor Inputs

(1)

Up to 16xRTD spot elements

(1)

Up to 8xRTD spot elements

(1)

Up to 4xRTD spot elements

(2)

None

Temperature Elements Wiring

4-wire or 3-wire (individual or common return)

3-wire (individual or common return)

(2)

None (for water level only, no temperature sensors)

Auxiliary Inputs

(2)

Rosemount 765 temperature and water level sensor input

None

Tankbus: Power and Communication

Bus powered 2-wire F

OUNDATION

fieldbus (IEC 61158)

Hazardous Location Certification

ATEX Intrinsic Safety

IECEx Intrinsic Safety

FM-US Intrinsic Safety

FM-Canada Intrinsic Safety

Brazil Inmetro Intrinsic Safety

KC Intrinsic Safety (South Korea)

CCOE/PESO Intrinsic Safety (India)

TIIS Intrinsic Safety (Japan)

Technical Regulations Customs Union (EAC) Intrinsic Safety

No Hazardous Location Certification

Summary of Contents for Rosemount 2240S



































































































































































































Search results

Summary of Contents for Rosemount 2240S

Reviews:

Emerson Rosemount 2240S, Reference Manual, Page: 156 / 194

Search results

Summary of Contents for Rosemount 2240S

Reviews: