manualshive.com logo in svg

Emerson Rosemount 2240S, Reference Manual, Page: 17 / 194

Share
Download
Emerson Rosemount 2240S Reference Manual Download Page 17

7

Reference Manual 

00809-0100-2240, Rev DA

Overview

October 2017

Overview

Section 2

Overview

Introduction   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 7
Components  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 8
System overview   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 9
Getting started  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 16
Installation procedure  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 17

2.1

Introduction

The Rosemount

™

 2240S Multi-input Temperature Transmitter can connect up to sixteen 3- or 4-wire 

temperature spot elements and an integrated water level sensor. The Rosemount 2240S sends 
measurement data, such as temperature and water level, via the intrinsically safe 2-wire Tankbus

(1)

, to a 

Rosemount 2410 Tank Hub. Measurement data and status information can be viewed on a PC with the 
Rosemount TankMaster software, as well as on the integral display of the tank hub and the Rosemount 
2230 Graphical Field Display.
Data from a group of tanks is buffered by a Rosemount 2460 System Hub, and is distributed to a 
Rosemount TankMaster PC, or another host system, whenever the system hub receives a request for 
data. In case no system hub is included in the system, the tank hub can communicate directly with the 
host computer.

Figure 2-1. System integration

1. 

The intrinsically safe Tankbus complies with the FISCO F

OUNDATION

™ fieldbus standard.

Rosemount 
TankMaster

Rosemount 2410 Tank Hub

Modem

Rosemount 2460 
System Hub

Relay Outputs

Secondary Bus (Non-IS)

Primary Bus

 Tankbus

Rosemount 2240S 
Temperature 
Transmitter

Rosemount 2230 
Graphical Field Display

Host

Zone 1

Zone 0

Rosemount 5900S 
Radar Level Gauge

Secondary bus (IS)

Servo 
gauges

Summary of Contents for Rosemount 2240S



































































































































































































Reviews:

No comments