manualshive.com logo in svg

Elmo Pro v.1.403.16, User Manual

Share
Download
Elmo Pro v.1.403.16 User Manual Download Page 121

C. Select any sensor to view more details (Begin Time, End Time and Filter). In this example, Sensors 1 and

2 were selected. Both were associated with channel 9

D. Recorded data can be further filtered by narrowing the time range. The filter column specifies the sensor

number.

Note

An Index Search can only be performed
within one calendar day.

c.

Select Motion Search

to view all video recorded when motion was detected

This information can be further filtered by selecting:

i.

Switch to Search by Motion

:

A. The first column will display all motion areas associated with specific channels, where motion was detected.

In this example, motion was detected in Area 1 of Channels 7,11 and 12

117

ELMO-PRO v.1.403.16 - User Manual

Advanced Search Panel

Chapter 1. ELMO-PRO Server

XML to PDF by RenderX XEP XSL-FO Formatter, visit us at 

http://www.renderx.com/

Summary of Contents for Pro v.1.403.16





























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands