Elmo Pro v.1.403.16 User Manual Download Page 104

Page: 104 / 156

There are three ways to send an email alert:

Triggered Sensor(s)

Select appropriate sensors in the

Enable Email For Sensor

frame. Whenever any of the selected sensors

are triggered, an e-mail alert will be sent to the configured e-mail address.

Tip

Make sure the sensors are enabled and
configured in the Hardware Setup.

Video Loss

Check the

Video Loss

checkbox in the Enable Email for Video Loss frame. When video loss is detected on one

or more channels, an e-mail alert will be sent to the configured e-mail address.

Scheduled Server Status

This section allows the user to configure scheduled e-mails to provide the server status. The email includes a snapshot
from the specified channel. To have the DVR send server status e-mails, fill in

Server Status

section:

a. Check the

Send Email

checkbox to enable server status e-mail alerts

b. Select the frequency of the automatic e-mails (1-24 hours) in the

Send Email Every

field. In the example

above, the server status email will be sent out every hour.

100

ELMO-PRO v.1.403.16 - User Manual

E-Mail Setup

Chapter 1. ELMO-PRO Server

XML to PDF by RenderX XEP XSL-FO Formatter, visit us at

http://www.renderx.com/

Summary of Contents for Pro v.1.403.16





























































































































































Search results

Summary of Contents for Pro v.1.403.16

Reviews:

Related manuals for Pro v.1.403.16

Brands by name

Popular brands

Elmo Pro v.1.403.16, User Manual

Search results

Summary of Contents for Pro v.1.403.16

Reviews:

Related manuals for Pro v.1.403.16

Brands by name

Popular brands