Eagle CUDA 350 S/MAP Installation And Operation Instructions Manual Download

Page: 99 / 180

Sonar Page

The Sonar Page displays the sonar chart, a view of the water column

from the surface to the bottom. The chart scrolls across the screen from

right to left, displaying signal echoes that represent fish, structure and

the bottom. The Sonar Page is discussed in detail in Sec. 3. To get to
the Sonar Page press

PAGES

→

ONAR

EXIT

Satellite Status Page

The Satellite Status GPS Page provides detailed information on the

status of the Cuda's satellite lock-on and position acquisition. To get to
the Satellite Status Page press

PAGES

←

to Map|

↓

ATELLITES

EXIT

No matter what Page display you are on, a flashing current position

indicator/question mark symbol and flashing GPS data displays indi-

cate satellite lock has been lost and no position has been acquired. The

Satellite Status Page shows you the quality and accuracy of the current

satellite lock-on and position calculation.

WARNING:

Do not begin navigating with this unit until the numbers
have stopped flashing!

Satellite Page. First page (left) indicates unit has not locked on to any

satellites and does not have a fix on its position. The second page (cen-

ter) shows satellites being scanned. The last page (right) shows satel-

lite lock-on with a 3D position.

Summary of Contents for CUDA 350 S/MAP




















































































































































































Search results

Summary of Contents for CUDA 350 S/MAP

Reviews:

Related manuals for CUDA 350 S/MAP

Brands by name

Popular brands

Eagle CUDA 350 S/MAP, Installation And Operation Instructions Manual

Search results

Summary of Contents for CUDA 350 S/MAP

Reviews:

Related manuals for CUDA 350 S/MAP

Brands by name

Popular brands