Eagle CUDA 350 S/MAP Installation And Operation Instructions Manual Download

Page: 57 / 180

Full sonar chart (left); split zoom (center); Digital data (right).

You can customize how the Sonar Page pictures and other data are dis-

played in many ways. We will discuss all of those features and options in

the Advanced Sonar Operation section, but to show you how easy the so-

nar unit is to operate, the following page contains a simplified, 10-step

quick reference that will cover most fish finding situations. The quick

reference describes how your unit will operate with all the sonar fea-

tures in their automatic modes, which are set at the factory.

Summary of Contents for CUDA 350 S/MAP




















































































































































































Search results

Summary of Contents for CUDA 350 S/MAP

Reviews:

Related manuals for CUDA 350 S/MAP

Brands by name

Popular brands

Eagle CUDA 350 S/MAP, Installation And Operation Instructions Manual

Search results

Summary of Contents for CUDA 350 S/MAP

Reviews:

Related manuals for CUDA 350 S/MAP

Brands by name

Popular brands