Eagle CUDA 350 S/MAP Installation And Operation Instructions Manual Download Page 158

Page: 158 / 180

150

To turn off WAAS alarm:

1. Press

MENU

↓

GPS

ETUP

ENT

↓

HOW

WAAS

LARM

2. With the option highlighted, press

ENT

to turn it on (check) or turn it

off (uncheck). After the option is set, press

EXIT

to return to the

main page display.

Software Version Information

From time to time, Eagle updates the operating system software in

some of its products. These software upgrades are usually offered to

customers as free downloads from our web site, www.eaglesonar.com.

These upgrades make the unit perform better or introduce a new fea-

ture or function. You can find out what software version is running in

your Cuda by using the Software Information command.

Main Menu with Software Information selected (left).

The Software Information screen (right).

1. Press

MENU

↓

YSTEM

ETUP

ENT

↓

OFTWARE

NFO

ENT

2. Read the information displayed on the screen.
3. To return to the main page display, press

EXIT

repeatedly.

Summary of Contents for CUDA 350 S/MAP




















































































































































































Search results

Summary of Contents for CUDA 350 S/MAP

Reviews:

Related manuals for CUDA 350 S/MAP

Brands by name

Popular brands

Eagle CUDA 350 S/MAP, Installation And Operation Instructions Manual

Search results

Summary of Contents for CUDA 350 S/MAP

Reviews:

Related manuals for CUDA 350 S/MAP

Brands by name

Popular brands