Eagle CUDA 350 S/MAP Installation And Operation Instructions Manual Download Page 29

Page: 29 / 180

Mark the center of each slot for the mounting screw pilot holes. You

will drill one hole in the center of each slot.
Drill the holes using the #29 bit (for the #10 screws).

Position transducer mount on transom and mark mounting holes.

Side view (left) and seen from above (right).

5. Attaching transducer to transom.

Remove the transducer from

the bracket and re-assemble it with the cable passing through the

bracket over the bolt as shown in the following figures.

Route cable over bolt and through bracket. Side view (left) and seen

from above (right).

Attach the transducer to the transom. Slide the transducer up or

down until it's aligned properly with the bottom of the hull as shown

in the preceding and following figures. Tighten the bracket's mount-

ing screws, sealing them with the sealant/adhesive compound.

Transom

Summary of Contents for CUDA 350 S/MAP




















































































































































































Search results

Summary of Contents for CUDA 350 S/MAP

Reviews:

Related manuals for CUDA 350 S/MAP

Brands by name

Popular brands

Eagle CUDA 350 S/MAP, Installation And Operation Instructions Manual

Search results

Summary of Contents for CUDA 350 S/MAP

Reviews:

Related manuals for CUDA 350 S/MAP

Brands by name

Popular brands