Eagle CUDA 350 S/MAP Installation And Operation Instructions Manual Download

Page: 141 / 180

133

NOTE:

When the position format is changed, it affects the way all positions

are shown on all screens. This includes waypoints.

To change the coordinate system, press

ENT

while

OORD

YSTEM

is high-

lighted at the top of the Coordinate System menu. Use

↑

↓

arrow keys

to select the desired format and press

ENT

To setup Loran TD:

1. From the Coordinate System menu, press

↓

ETUP

ORAN

and

press

ENT

NOTE:

If the Loran TD conversion is chosen, you must enter the local Lo-

ran chain identification for the master and slaves.

2. To access the Loran Chain, Secondary 1 or Secondary 2 menus, high-

light the category and press

ENT

Use the

↑

↓

keys to choose the desired

setting and press

ENT

Press

EXIT

to close the menu

Setup Loran TD highlighted on Coordinate System menu (left). Con-

figure Loran TD menu (right).

Summary of Contents for CUDA 350 S/MAP




















































































































































































Search results

Summary of Contents for CUDA 350 S/MAP

Reviews:

Related manuals for CUDA 350 S/MAP

Brands by name

Popular brands

Eagle CUDA 350 S/MAP, Installation And Operation Instructions Manual

Search results

Summary of Contents for CUDA 350 S/MAP

Reviews:

Related manuals for CUDA 350 S/MAP

Brands by name

Popular brands