Eagle CUDA 350 S/MAP Installation And Operation Instructions Manual Download

Page: 44 / 180

Align the bracket over the cable hole with the cable slots facing away

from you and fit the cable through one of the slots. Fasten the bracket

to the dash using the three screw holes.

Cuda 350 quick release mounting bracket. Slots in the base allow

routing the cable from beneath the mount.

Attach the unit to the bracket by first connecting the power/transducer

cable. Then, hold the sonar unit vertically and slide it onto the bracket

from above. (The back of the unit should be touching the front of the

bracket as you lower it into position.) As you push down, the unit will

lock into place with a distinct click.
To adjust the viewing angle, pinch the ratchets with one hand, then tilt

the unit with your other hand. Release the ratchets and the unit locks

into the new position. To dismount the unit for storage, press the ratch-

ets and lift the unit off the bracket.

Rear
(away from viewer)

Cable slot

Screw hole

Power/transducer cable

Ratchet

Summary of Contents for CUDA 350 S/MAP




















































































































































































Search results

Summary of Contents for CUDA 350 S/MAP

Reviews:

Related manuals for CUDA 350 S/MAP

Brands by name

Popular brands

Eagle CUDA 350 S/MAP, Installation And Operation Instructions Manual

Search results

Summary of Contents for CUDA 350 S/MAP

Reviews:

Related manuals for CUDA 350 S/MAP

Brands by name

Popular brands