Eagle CUDA 350 S/MAP Installation And Operation Instructions Manual Download Page 170

Page: 170 / 180

162

Menus for changing Com Port settings.

If you need additional assistance in configuring the unit to communicate

with another device, consult the factory. Customer service phone num-

bers are in the back of the unit's manual. To set Com Port Configuration:

1. Press

MENU

↓

YSTEM

ETUP

ENT

2. Press

↓

ORT

ENT

A menu appears with a drop-down Baud Rate selection box highlighted.

The menu also contains an on/off checkbox to activate NMEA Input,

NMEA Output, NMEA GPS Input and a button that allows you to

Configure NMEA.

To set Baud Rate:

With the Baud Rate box selected (the title bar should be highlighted in

black, as in the middle figure above), press

ENT

. A drop-down list ap-

pears, showing available baud rates. Select the one that matches the

baud rate on your VHF radio and press

ENT

To activate NMEA Output:

From the Communication Ports menu, press

↓

to highlight NMEA In-

put. Press

ENT

to turn on (check) or turn off (uncheck) the NMEA Input

checkbox.

Summary of Contents for CUDA 350 S/MAP




















































































































































































Search results

Summary of Contents for CUDA 350 S/MAP

Reviews:

Related manuals for CUDA 350 S/MAP

Brands by name

Popular brands

Eagle CUDA 350 S/MAP, Installation And Operation Instructions Manual

Search results

Summary of Contents for CUDA 350 S/MAP

Reviews:

Related manuals for CUDA 350 S/MAP

Brands by name

Popular brands