Eagle CUDA 350 S/MAP Installation And Operation Instructions Manual Download

Page: 82 / 180

changes on the screen as you press the up or down arrows. This is

handy when there is a lot of clutter in the water and you are match-

ing the sensitivity to rapidly changing water conditions.

Sonar Menu with Sensitivity command selected (left).

The Sensitivity Control Bar (right).

To adjust sensitivity in manual mode:

1. First, turn off Auto Sensitivity. From the Sonar Page, press

MENU

↓

UTO

ENSITIVITY

ENT

2. Press

↑

ENSITIVITY

ENT

and the Sensitivity Control Bar appears.

Press

↓

↑

to pick a different sensitivity setting. When it is set at the

desired level and press

EXIT

NOTE:

To return to the original factory setting for Auto Sensitivity, see the

entry in this section on Reset Options. If sensitivity is in manual

mode, the Reset Options command will switch back to Auto and re-

set the factory setting at the same time.

Set Keel Offset

This unit measures water depth from the face of the transducer. Since

the transducer is installed below the water surface, the distance dis-

played by the digital depth, chart depth scale, chart cursor or fish sym-
bols is

not

the exact water depth.

Summary of Contents for CUDA 350 S/MAP




















































































































































































Search results

Summary of Contents for CUDA 350 S/MAP

Reviews:

Related manuals for CUDA 350 S/MAP

Brands by name

Popular brands

Eagle CUDA 350 S/MAP, Installation And Operation Instructions Manual

Search results

Summary of Contents for CUDA 350 S/MAP

Reviews:

Related manuals for CUDA 350 S/MAP

Brands by name

Popular brands