Eagle CUDA 350 S/MAP Installation And Operation Instructions Manual Download Page 62

Page: 62 / 180

Sonar Menu with Sensitivity command selected (left).

Sensitivity Control Bar (right).

NOTE:

If you want to change the sensitivity in Manual Mode, turn off Auto
Sensitivity. From the Sonar Page, press

MENU

↓

UTO

ENSITIV-

ITY

ENT

↑

ENSITIVITY

ENT

. Press

↓

↑

to pick a different sensi-

tivity setting. When it is set at the desired level, press

EXIT

Tip:

While you are experimenting and learning, it is possible to scram-

ble the settings so the sonar picture disappears from the screen. If

that happens, remember it is easy to switch back to full automatic

operation by restoring the factory default settings.

To Restore Factory Settings

1. Press

MENU

↓

YSTEM

ETUP

ENT

↓

ESET

P-

TIONS

ENT

2. A reset options confirmation message will appear. Select

and

press

ENT

. All options are reset and the unit reverts back to the

original settings.

Summary of Contents for CUDA 350 S/MAP




















































































































































































Search results

Summary of Contents for CUDA 350 S/MAP

Reviews:

Related manuals for CUDA 350 S/MAP

Brands by name

Popular brands

Eagle CUDA 350 S/MAP, Installation And Operation Instructions Manual

Search results

Summary of Contents for CUDA 350 S/MAP

Reviews:

Related manuals for CUDA 350 S/MAP

Brands by name

Popular brands