Eagle CUDA 350 S/MAP Installation And Operation Instructions Manual Download

Page: 163 / 180

155

New Trail

To manually start a new trail in the Trails Menu, make sure

RAIL

is selected and press

ENT

. You will be directed to the Edit Trail screen.

Trail Visible/Invisible and Other Trail Options

The name, active and visible settings and maximum number of points

in the trail, all are accessed on the Edit Trail menu. The Active setting

determines whether or not the unit is recording new points for a par-
ticular trail. On the Edit Trail menu, press

↓

↑

to highlight the section

you want to change, then press

ENT

. Make your changes, then press

EXIT

to close this menu.

Units of Measure

This menu sets the units of measure used for Speed and Distance,

Depth, Temperature, Altitude and Heading.

To change units of measure:

Press

MENU

↓

YSTEM

ETUP

ENT

Units of Measure on System Setup menu (left).

Units of Measure Menu (right).

To set Units of Measure:

Press

↓

to the desired units, then press

ENT

to turn a unit on or off

After all options are set, press

EXIT

to re-

turn to the main page display.

Summary of Contents for CUDA 350 S/MAP




















































































































































































Search results

Summary of Contents for CUDA 350 S/MAP

Reviews:

Related manuals for CUDA 350 S/MAP

Brands by name

Popular brands

Eagle CUDA 350 S/MAP, Installation And Operation Instructions Manual

Search results

Summary of Contents for CUDA 350 S/MAP

Reviews:

Related manuals for CUDA 350 S/MAP

Brands by name

Popular brands