Eagle CUDA 350 S/MAP Installation And Operation Instructions Manual Download

Page: 112 / 180

104

3. If the list is short, you can jump directly to the

IND

IST

box by

pressing

ENT

. Use

↑

↓

to select the waypoint name, press

ENT

and the

waypoint information screen appears with the

command selected.

4. To begin navigating to the waypoint, press

ENT

Find by Name highlighted (left). Find By Name menu (center). Way-

point information screen (right).

Set Man Overboard (MOB) Waypoint

One of boating's most terrifying events is having a friend or family

member fall overboard. It is particularly dangerous at night or if there

is no land in sight.This unit has a man overboard feature that shows

navigation data to the location where the feature was activated. To ac-

tivate it, press the

ZOUT

and

ZIN

keys at the same time. Your position

at the time these keys are pressed is used as the man overboard posi-

tion.

Caution:

Saving a new Man Overboard waypoint will overwrite and erase
the previous Man Overboard waypoint.

Navigate Back to MOB Waypoint

Find your way back to the accident position with the Navigation Page

or Map Page. When MOB is activated, the Navigation Page automati-

Summary of Contents for CUDA 350 S/MAP




















































































































































































Search results

Summary of Contents for CUDA 350 S/MAP

Reviews:

Related manuals for CUDA 350 S/MAP

Brands by name

Popular brands

Eagle CUDA 350 S/MAP, Installation And Operation Instructions Manual

Search results

Summary of Contents for CUDA 350 S/MAP

Reviews:

Related manuals for CUDA 350 S/MAP

Brands by name

Popular brands