Eagle CUDA 350 S/MAP Installation And Operation Instructions Manual Download

Page: 166 / 180

158

Com port wiring to transmit NMEA information

to a Uniden or similar VHF radio or other device.

Twist the appropriate wires together, making sure that the exposed

ends make good contact. Secure the wire ends with wire nuts, then

wrap each wire nut securely with electrical tape to protect against

moisture, as shown in the figure on the right.

After taping the wire ends individually, wrap the entire connection

with electrical tape as shown. This will help protect from moisture and

prevent the wires from breaking contact.

Ground/Shield or NMEA –

To Uniden

radio or other

device

om port to

Cuda 250

Yellow (Transmit)

NMEA Wire (Receive) or NMEA +

Shield (Ground)

Summary of Contents for CUDA 350 S/MAP




















































































































































































Search results

Summary of Contents for CUDA 350 S/MAP

Reviews:

Related manuals for CUDA 350 S/MAP

Brands by name

Popular brands

Eagle CUDA 350 S/MAP, Installation And Operation Instructions Manual

Search results

Summary of Contents for CUDA 350 S/MAP

Reviews:

Related manuals for CUDA 350 S/MAP

Brands by name

Popular brands