Eagle CUDA 350 S/MAP Installation And Operation Instructions Manual Download

Page: 117 / 180

109

New trail, named Trail 3, is created when Trail 2 is made inactive. Any

new travel will be recorded in this trail, which is active and visible.

Trails do not need to be visible in order to be active.

You can save and recall up to 10 different plot trails.

Tip:

Another quick way to stop recording one trail and begin a new one
is to use the New Trail command. Press

MENU

↓

RAILS

ENT

. Use

→

to select

RAIL

and press

ENT

Caution:

You also have the option of completely turning off trail re-
cording, under the trail Options command. If, however, the Up-
date Active Trail option is left turned off, it will cancel the
automatic trail creation feature.

Displaying a Saved Trail

The active trail is automatically displayed on the with the default set-

tings. You can selectively turn trail display on and off for any saved or

active trail. In the Saved Trails List, visible trails have a check mark in

front of the trail name.

Summary of Contents for CUDA 350 S/MAP




















































































































































































Search results

Summary of Contents for CUDA 350 S/MAP

Reviews:

Related manuals for CUDA 350 S/MAP

Brands by name

Popular brands

Eagle CUDA 350 S/MAP, Installation And Operation Instructions Manual

Search results

Summary of Contents for CUDA 350 S/MAP

Reviews:

Related manuals for CUDA 350 S/MAP

Brands by name

Popular brands