Eagle CUDA 350 S/MAP Installation And Operation Instructions Manual Download

Page: 101 / 180

you've just taken — is depicted by the line extending from the arrow.

The arrow pointing down at the top of the compass rose shows your cur-

rent track (direction of travel).

Navigation Page, recording a trail, traveling north. The page looks like

this when the unit is not navigating to a waypoint, following

a route, or backtracking a trail.

When navigating to a waypoint, the Navigation screen looks like the

following figure. Your ground speed, track, distance and bearing to

waypoint and course are all shown digitally on this screen.

NOTE:

Remember: when Speed, Track and Position information displays

are flashing, satellite lock has not been acquired and no position fix

has been determined. A question mark will also flash on the pre-

sent position arrow in the center of the compass rose.

Compass

rose

Navigation
information
displays

Present

position

arrow

Trail line

Track or compass heading indicator, showing direction of travel

Summary of Contents for CUDA 350 S/MAP




















































































































































































Search results

Summary of Contents for CUDA 350 S/MAP

Reviews:

Related manuals for CUDA 350 S/MAP

Brands by name

Popular brands

Eagle CUDA 350 S/MAP, Installation And Operation Instructions Manual

Search results

Summary of Contents for CUDA 350 S/MAP

Reviews:

Related manuals for CUDA 350 S/MAP

Brands by name

Popular brands