Eagle CUDA 350 S/MAP Installation And Operation Instructions Manual Download

Page: 69 / 180

4. To set lower boundary for the Zone Alarm, use

←

→

to select

OWER

then press

↑

↓

to move the bottom of the bar to the desired depth.

5. Press

EXIT

repeatedly.

To switch to a different depth setting, open the Sonar Alarms menu

and repeat the instructions above, beginning with step 2.

Fish Alarm

Use the fish alarm for a distinctive audible alarm when fish or other
suspended objects are detected by the Fish I.D.

™

feature (Fish I.D.

must be turned on for the Fish Alarm to work). A different tone sounds

for each fish symbol size shown on the display.

Sonar Alarms menu with Fish Alarm selected. The check box

to the left is checked, indicating the alarm is turned on.

To turn the fish alarm on:

1. Press

MENU

↓

LARMS

ENT

2. Press

↓

ONAR

LARMS

ENT

3. Press

↓

ISH

LARM

NABLED

and press

ENT

to turn on (check) the

alarm. Press Exit repeatedly to get back to the main page display.

Summary of Contents for CUDA 350 S/MAP




















































































































































































Search results

Summary of Contents for CUDA 350 S/MAP

Reviews:

Related manuals for CUDA 350 S/MAP

Brands by name

Popular brands

Eagle CUDA 350 S/MAP, Installation And Operation Instructions Manual

Search results

Summary of Contents for CUDA 350 S/MAP

Reviews:

Related manuals for CUDA 350 S/MAP

Brands by name

Popular brands