Eagle CUDA 350 S/MAP Installation And Operation Instructions Manual Download Page 33

Page: 33 / 180

Transducer angles and their effects on fish arches.

If the arch slopes up – but not back down – then the front of the trans-

ducer is too high and needs to be lowered. If only the back half of the

arch is printed, then the nose of the transducer is angled too far down

and needs to be raised.

NOTE:

Periodically wash the transducer's face with soap and water to re-

move any oil film. Oil and dirt on the face will reduce the sensitiv-

ity or may even prevent operation.

Transducer aimed

too far back

Transducer aimed

too far forward

Proper transducer angle

Partial fish arches

Full fish arch

Summary of Contents for CUDA 350 S/MAP




















































































































































































Search results

Summary of Contents for CUDA 350 S/MAP

Reviews:

Related manuals for CUDA 350 S/MAP

Brands by name

Popular brands

Eagle CUDA 350 S/MAP, Installation And Operation Instructions Manual

Search results

Summary of Contents for CUDA 350 S/MAP

Reviews:

Related manuals for CUDA 350 S/MAP

Brands by name

Popular brands