manualshive.com logo in svg

Eagle CUDA 350 S/MAP, Installation And Operation Instructions Manual

The Eagle CUDA 350 S/MAP is a versatile fish-finding device that offers advanced navigation technology. Ensure a seamless setup and optimal performance with the Installation And Operation Instructions Manual. Download this essential manual for free at manualshive.com, providing step-by-step guidance for installation and operation of your Eagle CUDA 350 S/MAP.

Share
Download
background image

22 

Adjust the transducer so that it's parallel to the ground and tighten
the nut until it touches the outer washer, then add 1/4 turn. 

Don't

over tighten the lock nut!

 If you do, the transducer won't "kick-up" if

it strikes an object in the water. 

     

 

Align transducer centerline with hull bottom and attach to transom. 

6. Route the transducer cable through or over the transom to

the sonar unit.

 Make sure to leave some slack in the cable at the

transducer. If possible, route the transducer cable away from other

wiring on the boat. Electrical noise from the engine's wiring, bilge

pumps, VHF radio wires and cables, and aerators can be picked up by

the sonar. Use caution when routing the transducer cable around these

wires. 

WARNING: 

Clamp the transducer cable to the transom close to the 
transducer. This can prevent the transducer from enter-
ing the boat if it is knocked off at high speed. 

If you need to drill a hole in the transom to pass the connector through,

the required hole size is 5/8". 

Caution: 

If you drill a hole in the transom for the cable, make sure it is 
located above the waterline. After installation, be sure to seal the 
hole with the same marine grade above- or below-waterline seal-

Flat-bottom hull

Deep-"vee" hull

Bottom

of 

hull

Summary of Contents for CUDA 350 S/MAP





















































































































































































Reviews:

No comments

Related manuals for CUDA 350 S/MAP

Marcum Technologies Digital Sonar LX-i Owner'S Manual preview
Digital Sonar LX-i
Brand: Marcum Technologies Pages: 1

Brands by name

Popular brands

Load more brands