Eagle CUDA 350 S/MAP Installation And Operation Instructions Manual Download

Page: 49 / 180

Portable transducer assembly: rear view (left) and side view (right.)

Clean the chosen area of the hull before attaching the suction cup. Lo-

cate the transducer on the hull as shown in the following figure. Don't

allow the bracket to extend below the hull, because water pressure

against it can cause the suction cup to come off at speed.
Moisten the cup, then press it onto the hull as firmly as possible. Tie

the nylon cord to the boat and route the transducer cable to the sonar

unit. Your portable sonar is now ready for use.

Portable transducer installed on boat transom.

Hull

Suction

cup

Bracket

Transducer

Washer

Nut

Bolt

Screw

Suction

cup

Transducer

Tie nylon

cord here

Summary of Contents for CUDA 350 S/MAP




















































































































































































Search results

Summary of Contents for CUDA 350 S/MAP

Reviews:

Related manuals for CUDA 350 S/MAP

Brands by name

Popular brands

Eagle CUDA 350 S/MAP, Installation And Operation Instructions Manual

Search results

Summary of Contents for CUDA 350 S/MAP

Reviews:

Related manuals for CUDA 350 S/MAP

Brands by name

Popular brands