Eagle CUDA 350 S/MAP Installation And Operation Instructions Manual Download

Page: 31 / 180

ant/adhesive used for the mounting screws.

7. Make a test run to determine the results.

If the bottom is lost at

high speed, or if noise appears on the display, try sliding the trans-

ducer bracket down. This puts the transducer deeper into the water,

hopefully below the turbulence causing the noise. Don't allow the

transducer bracket to go below the bottom of the hull!

TROLLING MOTOR BRACKET INSTALLATION

1. Attach the optional TMB-S bracket to the transducer as shown in the

following figure, using the hardware supplied with the transducer.

(Note: The internal tooth washer is supplied with the TMB-S.)

Attach motor mounting bracket to transducer.

2. Slide the adjustable strap supplied with the TMB-S through the slot

in the transducer bracket and wrap it around the trolling motor. Po-

sition the transducer to aim straight down when the motor is in the

water. Tighten the strap securely.

3. Route the transducer cable alongside the trolling motor shaft. Use

plastic ties (not included) to attach the transducer cable to the troll-

ing motor shaft. Make sure there is enough slack in the cable for the

motor to turn freely. Route the cable to the sonar unit and the trans-

ducer is ready for use.

Bolt

Internal tooth washer

Nut

Flat washer

TMB-S bracket

Summary of Contents for CUDA 350 S/MAP




















































































































































































Search results

Summary of Contents for CUDA 350 S/MAP

Reviews:

Related manuals for CUDA 350 S/MAP

Brands by name

Popular brands

Eagle CUDA 350 S/MAP, Installation And Operation Instructions Manual

Search results

Summary of Contents for CUDA 350 S/MAP

Reviews:

Related manuals for CUDA 350 S/MAP

Brands by name

Popular brands