Eagle CUDA 350 S/MAP Installation And Operation Instructions Manual Download

Page: 22 / 180

Your Skimmer transducer typically comes packaged with a one-piece

stainless steel bracket for mounting it to the transom of your boat. The

optional trolling motor mount uses a one-piece plastic bracket with an

adjustable strap. These are "kick-up" mounting brackets. They help pre-

vent damage if the transducer strikes an object while the boat is moving.

If the transducer does "kick-up," the bracket can easily be pushed back

into place without tools.

Read these instructions carefully

before

attempting the installation.

Determine which of the installation methods is right for your boat.

Remember, the transducer location and installation is the most

critical part of a sonar installation.

Recommended Tools and supplies

If you prefer the option of routing the cable through the transom, you will

need a 5/8" drill bit.

NOTE:

The following installation types also call for these recommended

tools and required supplies that you must provide (supplies listed
here are

not

included):

Transom installation

Tools include: two adjustable wrenches, drill, #29 (0.136") drill bit, flat-
head screwdriver. Supplies:

high quality, marine grade

above- or below-

waterline sealant/adhesive compound.

Trolling motor installations

Tools: two adjustable wrenches, flat-head screwdriver. Supplies: plastic

cable ties.

Shoot-through hull installations

Tools: these will vary depending on your hull's composition. Consult your

boat dealer or manufacturer. Other tools are a wooden craft stick or

similar tool for stirring and applying epoxy, and a paper plate or piece

of cardboard to mix the epoxy on. Supplies: rubbing alcohol, 100 grit

Summary of Contents for CUDA 350 S/MAP




















































































































































































Search results

Summary of Contents for CUDA 350 S/MAP

Reviews:

Related manuals for CUDA 350 S/MAP

Brands by name

Popular brands

Eagle CUDA 350 S/MAP, Installation And Operation Instructions Manual

Search results

Summary of Contents for CUDA 350 S/MAP

Reviews:

Related manuals for CUDA 350 S/MAP

Brands by name

Popular brands