Dräger Fabius 4116029 Technical & Service Manual Download Page 60

Page: 60 / 328

Fabius

Function Description

2-52

Cop

ight

2000 Dr

aeger

edical,

sec2_

funcde

scr

ip_

b.fm

10.5.1

Microcontroller

The microcontroller 80C517A controls the functions of the Power PCB.

10.5.2

Quartz Oscillator

The quartz oscillator of the Control PCB clocks the microcontroller 80C517A with
12 MHz.

10.5.3

EPROM

The EPROM has a programmable area of 512 kbytes.

10.5.4

Latch

The latch HC373 is a driver block.

10.5.5

MOSFET Amplifier

The MOSFET amplifier controls the motor of the ventilator.

10.5.6

Voltage Transformer for the Backlighting Lamp

The voltage transformer E1241 transforms the input voltage into a corresponding
output voltage for the lamp of the backlighting.

10.5.7

PEEP Valve Control

The power field-effect transistor BUZ20 and the operational amplifier LM324 control
the PEEP valve.

10.5.8

Light Barrier Evaluation of the Motor

The IC 74HC14 evaluates the final position and the movement of the motor
(END-SCH, PHASE0, and PHASE1).

Risk of damage to the voltage transformer.

The voltage transformer will be damaged if used at no load.

Do not

operate the voltage transformer without the lamp of the
backlighting

RETURN TO CD-ROM TABLE OF CONTENTS

RETURN TO THIS MANUAL'S TABLE OF CONTENTS

Summary of Contents for Fabius 4116029








































































































































































































































































































































Search results

Summary of Contents for Fabius 4116029

Reviews:

Dräger Fabius 4116029, Technical & Service Manual, Page: 60 / 328

Search results

Summary of Contents for Fabius 4116029

Reviews: