Dräger Fabius 4116029 Technical & Service Manual Download Page 155

Page: 155 / 328

Fabius

Repair Instructions

3-87

Cop

ight

2000 Dr

aeger

edical,

sec3_r

epai

rinstruc_c.fm

• Secure respective pressure regulator to gas box using locknut

Fig. 72:

Adjusting/securing pressure regulator

15.4.3

Adjusting the Pressure Regulator

• Use a T-piece to connect a separate pressure gauge (range: 0 to 6 bar) to outlet

of pressure regulator to be adjusted.

• Reconnect hoses (according to previously applied markings).

• Adjust a flow of 1 L/min and set O

pressure regulator to 3.0 bar ±0.2 bar using

adjusting ring

(see Figure "Adjusting/securing pressure regulator").

(Pressure regulator can be opened by turning adjusting ring clockwise).

• Adjust a flow of 1 L/min and set N

O pressure regulator to 2.0 bar ±0.2 bar using

adjusting ring

(see Figure "Adjusting/securing pressure regulator").

(Pressure regulator can be opened by turning adjusting ring clockwise).

• Adjust a flow of 1 L/min and set AIR pressure regulator to 1.5 bar ±0.2 bar using

adjusting ring

(see Figure "Adjusting/securing pressure regulator").

(Pressure regulator can be opened by turning adjusting ring clockwise).

• Push adjusting ring

downward in order to fix set value.

• Remove T-piece and separate pressure gauge from gas box.

• Check that hose system is free of leaks (for example by using leak detector

spray).

• Reassemble Fabius using the reverse method of that used for disassembly.

• Check pressure regulator function according to Test Certificate.

RETURN TO CD-ROM TABLE OF CONTENTS

RETURN TO THIS MANUAL'S TABLE OF CONTENTS

Summary of Contents for Fabius 4116029








































































































































































































































































































































Search results

Summary of Contents for Fabius 4116029

Reviews:

Dräger Fabius 4116029, Technical & Service Manual, Page: 155 / 328

Search results

Summary of Contents for Fabius 4116029

Reviews: