manualshive.com logo in svg

Dräger Fabius 4116029, Technical & Service Manual, Page: 122 / 328

Share
Download
Dräger Fabius 4116029 Technical & Service Manual Download Page 122

Fabius

®

Repair Instructions

 

3-54

Cop

yr

ight

 2000 Dr

aeger

 M

edical,

 In

c.

sec3_

repa

ir

instr

uc_c.

fm

 

14.14

Pressure Sensor (Paw) on Control PCB

In case of failure, replace the complete pressure sensor (Paw) on the Control PCB. 
After replacement, calibrate the pressure sensor (Paw) in the DrägerService Mode.

14.14.1 Testing the Pressure Sensor (Paw)

• Test pressure sensor (Paw) in the debug mode: “P” and “Plat”.

14.14.2 Dismounting/Replacing the Pressure Sensor (Paw)

• Switch control box off using ON/OFF switch (ON/OFF switch is located on rear 

panel of control box).

• Remove control box from Gas Box (see "Removing the Control Box from the Gas 

Box").

• Remove lateral screws 

1 

from control box 

2

 and lift top cover 

3

 in direction of 

A

 

and away from control box 

2

.

• Place top cover 

3

 of control box 

2

 aside.

Fig. 35:

Front view of control box, removing top cover

Electrostatic discharge can damage electrostatic sensitive 
devices. Use a static-dissipative mat and a wrist strap when 
handling electrostatic sensitive devices.

1..2..

Menu

PEEP

IPPV

man./

spont.

Pmax

TI:TE

TIP:TI

f

IPPV

V

T

IPPV
Paw [mbar]

FiO2

MV

Paw

60
40
20

0

24

7.9

28

0

80

21

12.0

3.0

40

8

1

1

A

2

3

RETURN TO CD-ROM TABLE OF CONTENTS

RETURN TO THIS MANUAL'S TABLE OF CONTENTS

Summary of Contents for Fabius 4116029









































































































































































































































































































































Reviews:

No comments