Dräger Fabius 4116029 Technical & Service Manual Download Page 182

Page: 182 / 328

Fabius

Repair Instructions

3-114

Cop

ight

2000 Dr

aeger

edical,

sec3_

repa

instr

uc_c.

19.2.5

Checking/Adjusting the O

Control Pressure

• Connect a pressure gauge (measuring range 100 mbar) to O

side inlet port

using a T-piece.

• Adjust O

flow control valve to 0.20 L/min.

The control pressure should be 25 mbar (±1 mbar).

• If the control pressure is not 25 mbar (±1 mbar) use adjusting screw

to adjust

the control pressure on the O

side.

Fig.102:

S-ORC, adjusting the O

control pressure

RETURN TO CD-ROM TABLE OF CONTENTS

RETURN TO THIS MANUAL'S TABLE OF CONTENTS

Summary of Contents for Fabius 4116029








































































































































































































































































































































Search results

Summary of Contents for Fabius 4116029

Reviews:

Dräger Fabius 4116029, Technical & Service Manual, Page: 182 / 328

Search results

Summary of Contents for Fabius 4116029

Reviews: