Dräger Fabius 4116029 Technical & Service Manual Download Page 193

Page: 193 / 328

Fabius

Repair Instructions

3-125

Cop

ight

2000 Dr

aeger

edical,

sec3_r

epai

rinstruc_c.fm

• Disconnect ventilator connector

from uninterruptible power supply.

• Push ventilator connector back into ventilator compartment.

Fig.113:

Rear view of Fabius, disconnecting the ventilator connector

• Hold patient system in place (to prevent ventilator from falling down) and remove

fixing screw and washer

Fig.114:

Top view of Fabius, removing fixing screw and washer

• Place ventilator on a stable surface.

20.4

Dismounting/Replacing the Motor

In case of failure, replace the complete ventilator with a new one.

RETURN TO CD-ROM TABLE OF CONTENTS

RETURN TO THIS MANUAL'S TABLE OF CONTENTS

Summary of Contents for Fabius 4116029








































































































































































































































































































































Search results

Summary of Contents for Fabius 4116029

Reviews:

Dräger Fabius 4116029, Technical & Service Manual, Page: 193 / 328

Search results

Summary of Contents for Fabius 4116029

Reviews: