Desoutter Delta Wrench 150 Nm User Manual Download Page 44

Page: 44 / 184

Part Number
Issue
Date
Page

6159937790
12
03/2018
44 / 184

03/2018

44 (184)

4.2

DeltaQC Overview

Click on the DeltaQC icon to launch the software.

After connecting the Delta Wrench to the PC (refer to the paragraph

“

Connecting to the Delta

Wrench

”), the following main menu is shown:

NOTE

: The DeltaQC adapts automatically to the Delta Wrench type and firmware version;

therefore, some menus or commands may be hidden or disabled, if not supported by your
version of the Delta Wrench.

Working in the Delta Wrench Map area (

Online mode

), all the data are directly written in the Delta

Wrench connected.

Working

Offline

, it is possible to define the test programs and transfer them to the Delta Wrench at a

later time. The DeltaQC stores the following data in a local database:

•

Test programs (Psets)

•

Test results

•

Tools

•

Test curves

NOTE

: Refer to the paragraph “

Offline mode

” for further details.

Assembly Line

details area

Build area

Log area

Assembly Line area

Status bar

Menu list

Toolbar

Summary of Contents for Delta Wrench 150 Nm

























































































































































































Search results

Summary of Contents for Delta Wrench 150 Nm

Reviews:

Desoutter Delta Wrench 150 Nm, User Manual, Page: 44 / 184

Search results

Summary of Contents for Delta Wrench 150 Nm

Reviews: