manualshive.com logo in svg

Desoutter Delta Wrench 150 Nm, User Manual, Page: 174 / 184

Share
Download
Desoutter Delta Wrench 150 Nm User Manual Download Page 174

 

Part Number 
Issue  
Date 
Page 

6159937790 
12 
03/2018 
174 / 184 

 

03/2018 

 

174 (184) 

15.1 

Delta Wrench Diagnostic 

The diagnostic menu makes a check of the Delta Wrench hardware. 

Select 

Diagnostic

 from the 

Settings

 menu to start the diagnostic procedure: 

 
The diagnostic procedure leads the user to examine the hardware of the Delta Wrench.  

The  diagnostic  procedure  is  interactive:  simply  follow  the  instructions  given  on  the  Delta  Wrench 
display to complete the diagnostic. In case a test gives a 

Not OK 

result during the test, it means that 

the related component needs to be repaired or replaced. 

 

NOTE

: If the test on some buttons of the Delta Wrench keyboard gives 

Not OK

 result, all the 

following  tests  requiring  the  operator  to  use  that  button  to  confirm  the  test  result  will  not  be 
performed, and will be marked as 

N.A.

 (Not Applicable). 

The  last  ten  diagnostic  reports  are  in  the  Delta  Wrench  memory.  It  is  possible  to  retrieve  each 
diagnostic report with the DeltaQC software.  
Connect the Delta Wrench to the DeltaQC and select the 

Controller 

→ Diagnostic

 menu:  

 
 
 

Summary of Contents for Delta Wrench 150 Nm

























































































































































































Reviews:

No comments