Desoutter Delta Wrench 150 Nm User Manual Download Page 120

Page: 120 / 184

Part Number
Issue
Date
Page

6159937790
12
03/2018
120 / 184

03/2018

120 (184)

8.2.1.13 WLAN/Open Protocol: number of results before wrench lock

WLAN/Open Protocol:
number of results before
wrench lock

This option is available only for Delta Wrench provided with a WLAN
radio module

When the WLAN radio module is enabled (for further details about
how to enable the WLAN radio module, refer to the chapter “

WLAN

Communication Protocol

”), the Delta Wrench can communicate with

a remote device via connection without cables.

If, during test, the Delta Wrench is out of transmission coverage, the
option “

WLAN/Open Protocol: number of resu

lts before wrench lock”

defines the number of results allowed before to completely lock the
Delta Wrench.

It is possible to set the number of results before wrench lock by
selecting among the following options:

•

100

•

250

•

500

By default, the number of results before wrench lock is equal to

500

NOTE

: The option “

WLAN/Open Protocol: number of

results before wrench lock”

is disabled if it is set to

NOTE

: It is necessary to disable the radio module

connection before saving the “

WLAN/Open Protocol:

wrench lock

” parameter. The radio module connection is

disabled and enabled again automatically.

Once the Delta Wrench gets out of transmission coverage during
measurement,

and the “

number of results before wrench lock

” is

reached, the following Delta Wrench display is shown:

When the Delta Wrench returns within the transmission coverage,
the above “

Wrench Locked

” screen is no longer displayed and the

measure screen is shown again.

NOTE

: If the Delta Wrench is locked (out of transmission

coverage), no one Pset can start, even if the Delta Wrench
is switched off and on again.

Summary of Contents for Delta Wrench 150 Nm

























































































































































































Search results

Summary of Contents for Delta Wrench 150 Nm

Reviews:

Desoutter Delta Wrench 150 Nm, User Manual, Page: 120 / 184

Search results

Summary of Contents for Delta Wrench 150 Nm

Reviews: