Desoutter Delta Wrench 150 Nm User Manual Download Page 42

Page: 42 / 184

Part Number
Issue
Date
Page

6159937790
12
03/2018
42 / 184

03/2018

42 (184)

4.1.2

DeltaQC

“Evaluation version”

If DeltaQC Software is not registered after the installation, it works as

Evaluation

for 90 days; the

Evaluation

version provides all the functionalities of the registered version. When the trial period

expires, the software turns into

Free

version.

The number of days that remain for the trial period is shown on the bottom part of the DeltaQC
Software page (refer to the picture below):

4.1.3

DeltaQC

“Free version”

When the trial period expires, the software turns

from “

Demo

” into “

Free

” version.

The

Free

version has a limited set of function. It is possible only to define tightening programs (Pset),

review the results from the Delta Wrench (exporting them in an Excel file) and define the settings of
the instrument; all the other features are not available.

Evaluation
days remaining

Results Viewer

Controller

settings

Summary of Contents for Delta Wrench 150 Nm

























































































































































































Search results

Summary of Contents for Delta Wrench 150 Nm

Reviews:

Desoutter Delta Wrench 150 Nm, User Manual, Page: 42 / 184

Search results

Summary of Contents for Delta Wrench 150 Nm

Reviews: