Desoutter Delta Wrench 150 Nm User Manual Download Page 148

Page: 148 / 184

Part Number
Issue
Date
Page

6159937790
12
03/2018
148 / 184

03/2018

148 (184)

11.1

View One Curve

Select the curve to display by clicking on the bar placed at the top of the following screen:

When the Delta Wrench is connected to the DeltaQC Software (

online

mode), the last curve

performed can be recognized due to the

“

(LAST)

” placed close to the

curve number

The

Refresh

key (place on the left upper corner of the above screen) refreshes the window in case a

new curve is available.

When the Delta Wrench is not connected with the DeltaQC Software (

offline

mode), the

Delete

key

(placed on the right upper corner of the above screen) is available.

Refresh

key

Select among

25 curves

Delete

key

Selected curve

Toolbar

Summary of Contents for Delta Wrench 150 Nm

























































































































































































Search results

Summary of Contents for Delta Wrench 150 Nm

Reviews:

Desoutter Delta Wrench 150 Nm, User Manual, Page: 148 / 184

Search results

Summary of Contents for Delta Wrench 150 Nm

Reviews: