Home
/
Desoutter
/
Delta Wrench 150 Nm
/
User Manual

Desoutter Delta Wrench 150 Nm, User Manual, Page: 165 / 184

Share

Page: 165 / 184

Desoutter Delta Wrench 150 Nm User Manual Download Page 165

Part Number
Issue
Date
Page

6159937790
12
03/2018
165 / 184

165 (184)

03/2018

The WLAN module must be properly configured.

Connect the Delta Wrench by means of the USB cable to the PC where DeltaQC software is installed.

Start the DeltaQC software; then click on the “

Connect

” icon.

A

fter clicking on “

Controller

” icon, select “

Open Protocol settings

” item in the combo box shown (refer

to the picture below):

In the

Connection Info

page, enable the

Status

by clicking on the relative key (refer to the screen

below); if the

Status

is not enabled, the

Delta Wrench

cannot work with

Open Protocol

even if the

WLAN module is properly configured.

Radio Information

At the end of data entry,
store the data inserted
by clicking on

Store

key

Controller

icon

«
...
163
164
165
166
167
...
»

Summary of Contents for Delta Wrench 150 Nm

























































































































































































Reviews:

No comments