Desoutter Delta Wrench 150 Nm User Manual Download Page 156

Page: 156 / 184

Part Number
Issue
Date
Page

6159937790
12
03/2018
156 / 184

03/2018

156 (184)

Select the

Parameters

page to set the WLAN radio module parameters:

SSID

Enter the SSID name of the own wireless network.

WLAN

mode

Access Point

is selected.

Host name

Specify the name of the Delta Wrench; if there are more than one Delta
Wrench the names must be different.

Internet protocol
(TCP/IP)

Select

Enabled DHCP

if the network works with the DHCP protocol: the

Internet protocol configuration is set automatically.

On the other hand, it is possible to set manually the Internet Protocol
configuration by disabling the

DHCP

Port number

Specify the port number of the remote device that interfaces with the Delta
Wrench.

NOTE

: The

Port number

has to be set both if the user selects

TCP

Server

option and if the user selects

TCP Client

option.

IP address
(remote device)

Specify the IP address of the remote device that interfaces with the Delta
Wrench.

NOTE

: The

IP address (remote device)

has to be set ONLY if the

user selects

TCP Client

option.

At the end of data entry,

store the data inserted by

clicking on

Store

key

At the end of data entry,

store the data inserted by

clicking on

Store

key

TCP Server

option

TCP Client

option

Summary of Contents for Delta Wrench 150 Nm

























































































































































































Search results

Summary of Contents for Delta Wrench 150 Nm

Reviews:

Desoutter Delta Wrench 150 Nm, User Manual, Page: 156 / 184

Search results

Summary of Contents for Delta Wrench 150 Nm

Reviews: