manualshive.com logo in svg

Desoutter Delta Wrench 150 Nm, User Manual, Page: 21 / 184

Share
Download
Desoutter Delta Wrench 150 Nm User Manual Download Page 21

 

Part Number 
Issue  
Date 
Page 

6159937790 
12 
03/2018 
21 / 184 

 

21 (184) 

 

03/2018 

4 

WORKING WITH “DELTA QC” SOFTWARE 

 
 
    

 
 
 

 

DeltaQC is a PC software package developed to manage the Delta Wrench. 

It offers easy user-friendly programming and real time monitoring of the instrument. 

DeltaQC  serves  as  an  interface  between  the  user  and  the  Delta  Wrench. With  DeltaQC,  users  can 
configure the Delta Wrench, and receives the results and curves.  
The  main  features  that  characterize  the  interaction  between  DeltaQC  and  Delta  Wrench  are  as 
follows: 

•

  Psets definition 

•

  Review of results from the Delta Wrench 

•

  Review of curves from the Delta Wrench 

•

  Settings of the Delta Wrench 

 

 

NOTE

: DeltaQC saves the tightening programs, results and curves in a local database. 

4.1 

Software Installation 

 

NOTE

: Installation must be executed with PC administrator rights. Running the software also 

requires administrator rights (or the PC administrator password is needed when the software is 
started).

 

 

NOTE

:  Do  not  install  the  software  from  a  shared  folder/drive.  Install  the  software  from  the 

supplied CD/USB key; if the CD/USB key content is copied into a PC folder, it must be a PC 
local folder.

 

 

NOTE

: After installing the DeltaQC Software, install also the 

SQLServer2014 Express Edition

. 

Installation file is provided with the DeltaQC.  
See below for further installation details.

 

 
 

Delta 

Wrench 

USB 

DeltaQC 

Printer 

Excel File 

 

Summary of Contents for Delta Wrench 150 Nm

























































































































































































Reviews:

No comments