Danfoss VLT AutomationDrive Programming Manual Download Page 80

Page: 80 / 234

[4]

Enable / no
warning

Ready for operation. No start or stop
command is been given (start/disable).
No warnings are active.

[5]

VLT running

Motor is running and shaft torque is
present.

[6]

Running / no
warning

Output speed is higher than the speed
set in

1-81 Min Speed for Function at Stop

[RPM]

. The motor is running and there are

no warnings.

[7]

Run in
range/no
warning

Motor is running within the programmed
current and speed ranges set in

4-50 Warning Current Low

4-53 Warning

Speed High

. There are no warnings.

[8]

Run on
reference / no
warning

Motor runs at reference speed. No
warnings.

[9]

Alarm

An alarm activates the output. There are
no warnings.

[10]

Alarm or
warning

An alarm or a warning activates the
output.

[11]

At torque limit

The torque limit set in

4-16 Torque Limit

Motor Mode

4-17 Torque Limit Generator

Mode

has been exceeded.

[12]

Out of current
range

The motor current is outside the range
set in

4-18 Current Limit

[13]

Below current,
low

Motor current is lower than set in

4-50 Warning Current Low

[14]

Above current,
high

Motor current is higher than set in

4-51 Warning Current High

[15]

Out of speed
range

Output frequency is outside the
frequency ranges set in

4-52 Warning

Speed Low

and

4-53 Warning Speed High

[16]

Below speed,
low

Output speed is lower than the setting in

4-52 Warning Speed Low

[17]

Above speed,
high

Output speed is higher than the setting
in

4-53 Warning Speed High

[18]

Out of
feedback range

Feedback is outside the range set in

4-56 Warning Feedback Low

and

4-57 Warning Feedback High

[19]

Below
feedback low

Feedback is below the limit set in

4-56 Warning Feedback Low

[20]

Above
feedback high

Feedback is above the limit set in

4-57 Warning Feedback High

[21]

Thermal
warning

The thermal warning turns on when the
temperature exceeds the limit in the
motor, the Adjustable frequency drive,
the brake resistor, or the thermistor.

[22]

Ready, no
thermal
warning

Adjustable frequency drive is ready for
operation and there is no over-
temperature warning.

[23]

Remote, ready,
no thermal
warning

Adjustable frequency drive is ready for
operation and is in [Auto on] mode.
There is no over-temperature warning.

[24]

Ready, voltage
OK

Adjustable frequency drive is ready for
operation and the AC line voltage is
within the specified voltage range (see

General Specifications

section in the

Design Guide).

[25]

Reverse

Reversing. Logic ‘1’

when CW rotation of

the motor. Logic ‘0’ when CCW rotation
of the motor. If the motor is not rotating,
the output will follow the reference.

[26]

Bus OK

Active communication (no timeout) via
the serial communication port.

[27]

Torque limit
and stop

Use in performing a coasting stop and in
torque limit condition. If the Adjustable
frequency drive has received a stop signal
and is at the torque limit, the signal is
Logic ‘0’.

[28]

Brake, no brake
warning

Brake is active and there are no warnings.

[29]

Brake ready, no
fault

Brake is ready for operation and there are
no faults.

[30]

Brake fault
(IGBT)

Output is Logic ‘1’ when the brake IGBT is
short-circuited. Use this function to
protect the Adjustable frequency drive if
there is a fault on the brake modules. Use
the output/relay to cut out the AC line
voltage from the Adjustable frequency
drive.

[31]

Relay 123

The relay is activated when Control Word
[0] is selected in parameter group 8-**.

[32]

Mechanical
brake control

Enables control of an external mechanical
brake, see description in the section

Control of Mechanical Brake

, and

parameter group 2-2*

[33]

Safe stop
activated (FC
302 only)

Indicates that the safe stop on terminal
37 has been activated.