6-72 Terminal 45 Digital Output
Option:
Function:
[82]
SL digital output C
[83]
SL digital output D
[160] No alarm
[161] Running reverse
[165] Local ref active
[166] Remote ref active
[167] Start command activ
[168] Drive in hand mode
[169] Drive in auto mode
[170] Homing Completed
The homing operation is
completed. This option is only
effective when
parameter 37-00 Application Mode
is set to
[2] Position Control
.
[171] Target Position
Reached
The target position is reached. This
option is only effective when
parameter 37-00 Application Mode
is set to
[2] Position Control
.
[172] Position Control Fault
A fault occurred in the positioning
process. Refer to
parameter 37-18 Pos. Ctrl Fault
Reason
for details about the fault.
This option is only effective when
parameter 37-00 Application Mode
is set to
[2] Position Control
.
[173] Position Mech Brake
Selects mechanical control for
positioning. This option is only
effective when
parameter 37-00 Application Mode
is set to
[2] Position Control
.
[174] TLD indicator
Indicates whether the tension is
out of limit (
on
) during center
winding. This option is only
effective when
parameter 37-00 Application Mode
is set to
[1] Center winder
.
[175] Running on tension
Indicates whether tension PID
control is active (
on
) or inactive
(
off
). This option is only effective
when
is set to
[1] Center winder
.
[176] Ready to run
The center winder control is ready
to run. This option is only effective
when
is set to
[1] Center winder
.
[177] End of roll
The diameter limit is reached. This
option is only effective when
parameter 37-00 Application Mode
is set to
[1] Center winder
.
6-72 Terminal 45 Digital Output
Option:
Function:
[193] Sleep Mode
The frequency converter/system
has entered sleep mode. See
parameter group
22-4* Sleep Mode
.
[194] Broken Belt Function
A broken belt condition has been
detected. See parameter group
22-4* Sleep Mode
.
[198] Drive Bypass
6-73 Terminal 45 Output Min Scale
Range:
Function:
0 %
*
[0 -
200 %]
Scale for the minimum output (0 or 4 mA) of
the analog signal at terminal 45. Set the value
to be the percentage of the full range of the
variable selected in
.
6-74 Terminal 45 Output Max Scale
Range:
Function:
100 %
*
[0 -
200 %]
Scale for the maximum output (20 mA) of the
analog signal at terminal 45. Set the value to
be the percentage of the full range of the
variable selected in
6-76 Terminal 45 Output Bus Control
Range:
Function:
0
*
[0 - 16384 ] Holds the level of analog output if controlled
by bus.
4.7.5 6-9* Analog/Digital Output 42
Parameters for configuring the limits for analog/digital
output terminal 42. Analog outputs are current outputs:
0/4-20 mA. Resolution on analog outputs is 12 bit. Analog
output terminals can also be set up as digital output.
6-90 Terminal 42 Mode
Option:
Function:
Set terminal 42 to act as analog output or
as digital output.
[0]
*
0-20 mA
[1]
4-20 mA
[2]
Digital Output
6-91 Terminal 42 Analog Output
Option:
Function:
[0]
*
No operation
[100]
Output frequency
[101]
Reference
[102]
Process Feedback
[103]
Motor Current
[104]
Torque rel to limit
Parameter Descriptions
Programming Guide
MG06C602
Danfoss A/S © 7/2015 All rights reserved.
65
4
4
