Danfoss VLT Automation Drive FC 360, Programming Manual

Page: 134 / 156

Par. No. # Parameter description Default value 2-set-up Change
during
operation
Conversion
index
Type
8-50 Coasting Select [3] Logic OR All set-ups TRUE – Uint8
8-51 Quick Stop Select [3] Logic OR All set-ups TRUE – Uint8
8-52 DC Brake Select [3] Logic OR All set-ups TRUE – Uint8
8-53 Start Select [3] Logic OR All set-ups TRUE – Uint8
8-54 Reversing Select [3] Logic OR All set-ups TRUE – Uint8
8-55 Set-up Select [3] Logic OR All set-ups TRUE – Uint8
8-56 Preset Reference Select [3] Logic OR All set-ups TRUE – Uint8
8-57 PROFIdrive OFF2 Select [3] Logic OR All set-ups TRUE – Uint8
8-58 PROFIdrive OFF3 Select [3] Logic OR All set-ups TRUE – Uint8
8-7* Protocol Firmware Version
8-79 Protocol Firmware version ExpressionLimit 1 set-up FALSE -2 Uint16
8-8* FC Port Diagnostics
8-80 Bus Message Count 0 N/A 1 set-up TRUE 0 Uint32
8-81 Bus Error Count 0 N/A 1 set-up TRUE 0 Uint32
8-82 Slave Messages Rcvd 0 N/A 1 set-up TRUE 0 Uint32
8-83 Slave Error Count 0 N/A 1 set-up TRUE 0 Uint32
8-84 Slave Messages Sent 0 N/A 1 set-up TRUE 0 Uint32
8-85 Slave Timeout Errors 0 N/A 1 set-up TRUE 0 Uint32
8-88 Reset FC port Diagnostics [0] Do not reset 1 set-up TRUE – Uint8
8-9* Bus Feedback
8-90 Bus Jog 1 Speed 100 RPM All set-ups TRUE 67 Uint16
8-91 Bus Jog 2 Speed 200 RPM All set-ups TRUE 67 Uint16
5.2.10 9-** PROFIdrive
Par. No. # Parameter description Default value 2-set-up Change
during
operation
Conversion
index
Type
9-00 Setpoint 0 N/A All set-ups TRUE 0 Uint16
9-07 Actual Value 0 N/A All set-ups FALSE 0 Uint16
9-15 PCD Write Configuration ExpressionLimit 1 set-up TRUE – Uint16
9-16 PCD Read Configuration ExpressionLimit 1 set-up TRUE – Uint16
9-18 Node Address 126 N/A 1 set-up TRUE 0 Uint8
9-19 Drive Unit System Number 1037 N/A All set-ups TRUE 0 Uint16
9-22 Telegram Selection [100] None 1 set-up TRUE – Uint8
9-23 Parameters for Signals 0 All set-ups TRUE – Uint16
9-27 Parameter Edit [1] Enabled 1 set-up FALSE – Uint16
9-28 Process Control [1] Enable cyclic master 1 set-up FALSE – Uint8
9-44 Fault Message Counter 0 N/A All set-ups TRUE 0 Uint16
9-45 Fault Code 0 N/A All set-ups TRUE 0 Uint16
9-47 Fault Number 0 N/A All set-ups TRUE 0 Uint16
9-52 Fault Situation Counter 0 N/A All set-ups TRUE 0 Uint16
9-53 PROFIBUS Warning Word 0 N/A All set-ups TRUE 0 V2
9-63 Actual Baud Rate [255] No baudrate found All set-ups TRUE – Uint8
9-64 Device Identification 0 N/A All set-ups TRUE 0 Uint16
9-65 Profile Number 0 N/A All set-ups TRUE 0 OctStr[0]
9-67 Control Word 1 0 N/A All set-ups TRUE 0 V2
9-68 Status Word 1 0 N/A All set-ups TRUE 0 V2
9-70 Programming Set-up [9] Active Set-up 1 set-up TRUE – Uint8
9-71 PROFIBUS Save Data Values [0] Off All set-ups TRUE – Uint8
9-72 PROFIBUSDriveReset [0] No action 1 set-up FALSE – Uint8
Parameter Lists
VLT
®
AutomationDrive FC 360
132 Danfoss A/S © 7/2015 All rights reserved. MG06C602
5 5