Danfoss VLT Automation Drive FC 360, Programming Manual

Page: 144 / 156

5.2.24 37-** Application Settings
Par. No. # Parameter description Default value 2-set-up Change during
operation
Conversion
index
Type
37-0* Application Mode
37-00 Application Mode [0] Drive mode 1 set-up FALSE – Uint8
37-1* Position Control
37-01 Pos. Feedback Source [0] 24 V Encoder 1 set-up FALSE – Uint8
37-02 Pos. Target 0 N/A 1 set-up FALSE 0 Int32
37-03 Pos. Type [0] Absolute 1 set-up FALSE – Uint8
37-04 Pos. Velocity 100 RPM 1 set-up FALSE 67 Uint16
37-05 Pos. Ramp Up Time 5000 ms 1 set-up FALSE -3 Uint32
37-06 Pos. Ramp Down Time 5000 ms 1 set-up FALSE -3 Uint32
37-07 Pos. Auto Brake Ctrl [1] Enable 1 set-up TRUE – Uint8
37-08 Pos. Hold Delay 0 ms 1 set-up TRUE -3 Uint32
37-09 Pos. Coast Delay 200 ms 1 set-up TRUE -3 Uint16
37-10 Pos. Brake Delay 200 ms 1 set-up TRUE -3 Uint16
37-11 Pos. Brake Wear Limit 0 N/A 1 set-up TRUE 0 Uint32
37-12 Pos. PID Anti Windup [1] Enable 1 set-up TRUE – Uint8
37-13 Pos. PID Output Clamp 1000 N/A 1 set-up TRUE 0 Uint16
37-14 Pos. Ctrl. Source [0] DI 1 set-up TRUE – Uint8
37-15 Pos. Direction Block [0] No Blocking 1 set-up TRUE – Uint8
37-16 Pos. Power Recovery [1] Enable 1 set-up TRUE – Uint8
37-17 Pos. Ctrl Fault Behaviour [0] Ramp Down&Brake 1 set-up FALSE – Uint8
37-18 Pos. Ctrl Fault Reason [0] No Fault 1 set-up TRUE – Uint8
37-19 Pos. New Index 0 N/A 1 set-up TRUE – Uint8
37-2* Center Winder
1 set-up
37-20 Winder Mode Selection [0] Wind 1 set-up FALSE – Uint8
37-21 Tension Set Point 0% 1 set-up TRUE -1 Uint16
37-22 Taper Set Point 0% 1 set-up TRUE -1 Int16
37-23 Partial Roll Diameter Value 5% 1 set-up FALSE -3 Uint32
37-24 Core1 Diameter 5% 1 set-up FALSE -3 Uint32
37-25 Core2 Diameter 5% 1 set-up FALSE -3 Uint32
37-26 Winder Jog Speed 0% 1 set-up TRUE 0 Uint8
37-27 TLD Low Limit 0% 1 set-up TRUE -1 Uint16
37-28 TLD High Limit 0% 1 set-up TRUE -1 Uint16
37-29 TLD Timer 0.001 s 1 set-up TRUE -3 Uint16
37-30 TLDOnDelay [1] Enabled 1 set-up TRUE – Uint8
37-31 Diameter Limit Detector 100% 1 set-up TRUE -3 Uint32
37-32 Initial Diameter Measurement
[0] Set diameter when
diameter reset 1 set-up FALSE – Uint8
37-33 Diameter Measurement Input [0] No Function 1 set-up FALSE – Uint8
37-34 Reading at Core 0 N/A 1 set-up TRUE -2 Int16
37-35 Reading at Full Roll 0 V 1 set-up TRUE -2 Int16
37-36 Tension Set Point Input [0] Par.3721 1 set-up FALSE – Uint8
37-37 Taper Set Point Input [0] Par.3722 1 set-up FALSE – Uint8
37-38 Tension Feedback Input [0] No Function 1 set-up FALSE – Uint8
37-39 Tension Feedback Type [0] Load cell 1 set-up FALSE – Uint8
37-40 Center Winder Cmd Src
[1] Parameter
3754~3759 control the
functions 1 set-up TRUE – Uint8
37-41 Diameter Change Rate 0.001% 1 set-up TRUE -3 Uint8
37-42 Tapered Tension Change Rate 0.1% 1 set-up TRUE -1 Uint8
Parameter Lists
VLT
®
AutomationDrive FC 360
142 Danfoss A/S © 7/2015 All rights reserved. MG06C602
5 5